Triple Suction Cup Car Mount

  • This car Triple Suction Cup Car Mount can only be used with the Insta360 Action Invisible Selfie Stick - available to purchase separately (not included with the suction cup car mount), do not use with other selfie sticks. 
  • Say goodbye to limitations, with unique, third-person views of your car, or other video-game style angles.
  • Triple suction cups form a triangular structure for maximum stability.
  • Dual suction cup suitable for driving in cities and flat roads.
  • Three suction cups in one design, able to split into double suction cup holders or single suction cup holders if needed.
  • Individual suction cups with a static suction force of up to 20kg, holding firmly to your car.

Notes:

1. Please follow these instructions to install and use, do not perform DIY or connect third-party accessories. Failure or damage caused by not following the instructions is not covered by Insta360 warranty or exchange services;

2. This accessory is not recommended for use on public roads, please ensure that the surrounding road environment is safe before use.

3. This car Dual/Triple Suction Cup Car Mount can only be used with the Insta360 Action Invisible Selfie Stick, do not use with other selfie sticks.

4. Please use this product in a 0-40°C (32-104°F) ambient temperature environment.

5. Please try to install the suction cup on the same horizontal plane (or a plane with minimal slope). If it is not possible to install on the same horizontal plane, the suction cups on both sides of the horizontal support bar must be attached to the same plane, and the suction cups on the expansion support bar must be installed on the other plane.

6. Before mounting the suction cups, make sure that the surface is smooth and clean.

7. When mounting the suction cups, make sure that the suction cups have been completely fitted to the plane. If the suction cup does not fit, loosen the knob and adjust the angle of the suction cup; install the suction cup again and tighten the knob.

8. The white area on the piston is the indicator line. Observe this indicator line after the suction cup is installed. If the indicator line returns to the outside of the pump body for a short period of time (you can see the indicator line on the outside), there is an air leak and the suction cup needs to be reinstalled.

9. After installing the complete bracket, you need to make sure that all knobs on the bracket are tightened. Do not use the suction cup mount if the knobs cannot be tightened, or if the connection of the suction cup adapter, telescopic support rod or self-timer remains unlocked after all the knobs have been tightened.

10. When in use, if stopping for a break, please check the suction cup for any accidental air leakage (you can see the indicator line on the outside). If the suction cup has already leaked, please reattach the suction cup to prevent the bracket from falling and damaging the camera.

11. To remove the suction cups, pry the edges of the suction cups with your fingers to create a gap between the suction cups and the plane, then the suction cups can be easily removed.

12. After use, if the surface of the suction cup is dirty, you need to wipe it clean in time to ensure that the suction cup can maintain sufficient force when used next time.

13. When you mount this double/triple suction car mount, please do not use it in excessively rugged off-road conditions (including but not limited to large rocks, very bumpy, steep mountain roads), and do not drive the vehicle at speeds exceeding 100km/h (62 mph).

14. When you mount this double/triple suction car mount, please do not use it on roads other than smooth tarmac and do not drive the vehicle at speeds exceeding 80km/h (50mph).

15. The suction cups in this product are modular in design, when a single suction cup is used, it only supports to connect the Insta360 Action Invisible Selfie Stick. Keep it in a contracted state, do not expand the selfie stick.

16. The dynamic load of the suction cup mount is 300g when driving and the selfie stick is fully extended, please do not add heavy objects.

SKU INSTAX3-21
Barcode # 6970357856008
Brand Insta360
Shipping Weight 3.5000kg
Shipping Width 0.200m
Shipping Height 0.200m
Shipping Length 0.200m
Shipping Cubic 0.008000000m3

Be The First To Review This Product!

Help other Camzilla users shop smarter by writing reviews for products you have purchased.

Write a product review

You May Also Like